Perm Spoofer Setup Guide

Complete guide to setting up and using the Liteware Permanent Spoofer for hardware ID masking.

Introduction

The Liteware Perm Spoofer provides permanent hardware ID (HWID) masking at the firmware level. Unlike temporary spoofers, this solution modifies system-level components to provide long-lasting protection against hardware bans.

Important: Permanent spoofers make system-level changes that are difficult to revert. Always create a system restore point before proceeding.

Requirements

Before installing the Perm Spoofer, ensure your system meets the following requirements:

  • Operating System: Windows 10 (22H2/23H2) or Windows 11
  • Administrator Rights: Full administrator access is required
  • System Restore: Create a restore point before installation
  • Antivirus: Temporarily disable Windows Defender and other antivirus software
  • Activated License: A valid and activated Liteware license key
  • Hardware: Compatible with both AMD and Intel processors

Installation

Step 1: Preparation

  1. Create a System Restore Point
    Press Win + R, type rstrui.exe, and create a restore point named "Before Liteware Perm Spoofer"
  2. Disable Antivirus
    Temporarily disable Windows Defender and any third-party antivirus software
  3. Backup Important Data
    Ensure all important files are backed up before proceeding
Warning: Failure to create a restore point may result in system instability that requires a Windows reinstall to fix.

Step 2: Download

  1. Download the Perm Spoofer loader from the downloads section (requires activated key)
  2. Extract the files to a folder (e.g., C:\Liteware\PermSpoofer\)
  3. Ensure the folder is not scanned by antivirus (add to exclusions if needed)

Step 3: Driver Installation

  1. Right-click the loader executable and select "Run as Administrator"
  2. If prompted by Windows SmartScreen, click "More info" then "Run anyway"
  3. Follow the driver installation prompts
  4. Restart your computer when prompted

Activation

Before using the Perm Spoofer, you must activate your license key:

  1. Visit the Activate Key page
  2. Enter your license key
  3. Click "Activate License" and wait for confirmation
  4. Your key is now activated and ready to use

First Run

After installation and activation, follow these steps for your first run:

  1. Run the loader executable as Administrator
  2. Enter your activated license key when prompted
  3. Wait for authentication to complete
  4. The loader interface will appear

Configuration

The Perm Spoofer interface provides the following options:

CLEAN Button

The CLEAN button performs a comprehensive cleanup of Epic Games related files and registry entries. When clicked, you'll see a confirmation dialog:

Are you sure you want to proceed? This will cause Epic Games to get fully cleaned.

Click OK to proceed with the cleaning process. This will:

  • Execute multiple cleaning scripts (Fix Network Errors, MN_Cleaner_FN1-4)
  • Clean Epic Games registry entries
  • Remove Epic Games cache and temporary files
  • Reset network settings

SPOOF Button

The SPOOF button applies permanent hardware ID spoofing to your system:

  • MAC address spoofing
  • Disk serial spoofing
  • Motherboard information spoofing
  • BIOS/UEFI serial spoofing
  • System UUID spoofing
Note: The spoofing process may take a few minutes. Your computer may restart automatically during the process.

Using the Spoofer

Basic Spoofing Process

  1. Click the "SPOOF" button in the loader interface
  2. Read the confirmation message and click "OK"
  3. Wait for the spoofing process to complete (this may take several minutes)
  4. Your computer may restart automatically
  5. After restart, verify that spoofing was successful using the Serial Checker

Serial Checker

Use the Serial Checker feature to verify that your hardware IDs have been successfully spoofed:

  1. Click the "Serial Checker" button
  2. The checker will display your current hardware serials
  3. Compare with your previous serials to confirm changes

Verification

After spoofing, verify that the changes were applied successfully:

  1. Run the Serial Checker to view current hardware IDs
  2. Verify that MAC address, disk serials, and motherboard info have changed
  3. Test by launching a game with anti-cheat (EAC, BattlEye, Vanguard)
  4. Confirm that you can connect without hardware ban issues

Troubleshooting

Common Issues

Loader Won't Start

  • Ensure you're running as Administrator
  • Check that antivirus software is disabled
  • Verify your license key is activated
  • Try running from a different folder (not Desktop or Downloads)

Spoofing Fails

  • Ensure driver installation completed successfully
  • Check that all security software is disabled
  • Verify you have administrator privileges
  • Try running the CLEAN function first, then SPOOF

System Instability

  • Use System Restore to revert to before installation
  • Contact support if issues persist
Need Help? Join our Discord server for support from the development team and community.